How to Install a Vinyl Fence A vinyl fence is a beautiful low-maintenance method to delineate property lines and keep children and pets safe and secure. However, installing one yourself requires careful planning and focus on the finer points. First, you'll need to determine the required number of posts and then stake out the fence line. Generally fence posts should be placed 6 to 8 feet apart. Dig Postholes Use a power auger, or digger to dig postholes in your fence. Be sure to check with your local codes. The holes should be around 10 inches in diameter and deep enough to support about one-third of the length of the pole plus 6 inches of gravel backfill. Gate posts and main supports should usually be six inches higher than other posts in order to increase strength. After digging the posts then pour six inches of gravel into them. Then, fill them with quick-setting concrete. Follow the mixing and setting instructions on your concrete bag. The hollow post should be tapped into the concrete and then ensure that the post is level and plumb before moving on to the next. Consider installing drainage systems in case your fence is situated over a source of water to stop water from pooling in the holes. To stop erosion by water you could also add gravel between the fence & the ground. Contact cost to install vinyl fence before you start digging. They will mark underground lines. This will help you avoid unpleasant surprises, such as the possibility of a leaky water or sewer line, while installing your fence. Once you've marked the holes, dig each one to a depth of about 2.5 3' to 2.5'. The bottom of the hole should be wider than the top of the post, so that it will be able to fit inside the rails of the post when you put them in. Reduce the length of your posts. You must ensure that the posts are the same length if you want to put up vinyl fencing. This will allow the fence to bend but not break. This helps ensure that the fence is able to be able to withstand minor impacts as well as high winds. You can ensure that you have the same length of posts by using a level to measure them and then marking them on a string. You can either mark the strings on the ends of posts, or use them to line up each posthole. Once you have marked the posts, make holes to the required depth for the fence. They should be deep enough to hold 3 feet of post and 6 inches of gravel. This will form the post with a base that will help drain the water away. Then, insert vinyl fence install into each post and secure it with a self-drilling screw. This will prevent the top rail from slipping off the post and allow for movement in and out. Once the bottom rail has been installed Once the bottom rail is installed, slide your pickets across the u channel until you have completed the entire section. After that, you can slide in your middle and top rails. If you are installing a vinyl privacy fence, insert the u-channel before you hammer the top rail into the post. This will stop your fence from sliding in the winds, and will keep out bugs and debris. Install Posts If you are installing the fence made of vinyl you must adhere to the manufacturer's guidelines for installing the posts. Digging holes sufficient in depth to allow the posts to be supported is important. If you choose to use gravel as a base that requires digging holes 6 inches deeper. If you're installing a vinyl fence on slopes, it's important to ensure that the posts are level. This is because a higher post can cause the entire fence to lean, which makes it difficult for you to properly secure the panels. Before digging the hole Before digging, secure a string at the corners or ends of your posts to ensure they are straight. This will help you locate the exact location of your post. Ideally the posts should be 1/3 more deep than their length in order to provide them with more strength and stability. This can be done quickly and easily with a post-hole drill, or you can dig them manually. After the posts are set placed and the concrete is poured over them, you can pour it on. The cement should be around a foot deep and evenly spread. This will make the posts stronger and help them withstand strong winds. Once all the posts are in place after which you can connect rails to the posts. These rails snap into slots at the top and bottom of the posts. Once fence installation calculator have been secured to the posts, you can slide your vinyl fencing panels into place. Attach rails to posts Posts are the foundation of your vinyl fence and must be sturdy enough to support the weight of the fence. If the ground is sinking or shifting, the posts could move or tip, which could cause damage to your fence. Concrete in the base is the best method to ensure the stability of your posts. It isn't easy to connect a post to rails, but it is possible. To keep the post straight and level you can use a post brace. These boards are typically 2-foot by 4-foot and can be attached to the post using nails or using a clawhammer. Once fence installation calculator is secure and the rails are set on the top of it. If you are installing split rails move the rail that is on the bottom down until it is clear of one of the posts adjacent to it. Continue to add the rails until all of the posts are in place and the fence is complete. For pickets with spaced spacing, consult the local code enforcement department for specific spacing. If your fence is in a sloped area you might need to cut the pickets in an angled pattern. This isn't a necessity but it will help disguise the staggered boards ends. It is essential to choose the right style of fence for your property and landscape. The fence should be a part of the overall look of your property and offer security, privacy and curb appeal. A fence of the right style can help to reduce maintenance and repair costs. Attach rails to posts Vinyl fences are easy to install and are available in a wide range of styles. These include privacy fencing, split rails and picket fences. They are an attractive alternative to wood fences due to their strength and low maintenance. Before you dig holes for the posts the distance between each of the posts to ensure the fence is constructed in straight lines. Then, you should mark all the posts with a string and put them in the desired spot. Once the posts are ready to be drill, leave 5 to 6 inches above ground level for each hole. If you have a sloped property, concrete can be added to the bottom of each one. After the posts are erected, you can attach fence rails to them. Vinyl fence rails are available in two lengths, 8-foot and 16, so you can choose the size that best suits your home. If the fence has corners, you'll need to cut the rails in order to fit around the corner. You can make use of the end of one rail to slide it into the corner post and then the opposite end of the rail to slide it into the next post. After attaching the rails, put the fence pickets on the rails. This will give your fence a professional appearance. This will allow you to visually grade your fence so it looks consistent. Attach Posts to Other Posts Vinyl fences are a desirable option for homeowners who want to increase the curb appeal of their property and privacy while shielding their property from weather-related damage. They are also extremely robust and require very little maintenance. There are many types of vinyl fences available such as picket, solid privacy and picket. You can choose from a wide range of colors and sizes of fences. Some even come with a lifetime guarantee. When you're choosing a fence made of vinyl for your home, take into consideration the manufacturing method used by the manufacturer. Vinyl fencing is made in two ways: monoextrusion as well as co-extrusion. The first method injects polyvinyl chloride with UV inhibitors to avoid fade and chalking. The latter method uses two layers of PVC to create a capstock and substrate. In addition to these layers the vinyl fences are also injected with stabilizers and impact modifiers to make them strong and flexible. They are also resistant to rot and decay and some are covered by lifetime warranties. Ask your local dealer for assistance in deciding what type of vinyl fence to buy. They will be able to help you navigate in the right direction and recommend the best product for your requirements. If you've decided to install a fence made of vinyl for your home, it's time to start the installation. This phase of the project can be a bit challenging, so make sure to follow the instructions.
cost to install vinyl fence|vinyl fence install|fence installation calculator|fence installation calculator
